HOME | PRODUCTS | WHO USES | PRICES | ABOUT US | CONTACT |
Antenna Switch Control

Twelve Antennas and Eight Rotator Switch Control




  • Smart control for up to twelve-input antenna switch.
  • Band pass filter drive.
  • Band Data Output.
  • Automatic tuning for shortened antennas with high Q coils.
  • Control with auxiliar keyboard for Waller Flag Receiving
  • antennas manufactured by TOPBEAM.
  • Eight rotator Switch control
  • Antenna memory per Band
  • GPI/O to control external equipments
  • GPO Driven by frequency
  • Hot Switch Protection
  • No computer or software involved (PC less)
  • Interlock system to prevent more then on radio at the same antenna.
  • LAN for external remote control.
  • Control all Hamplus (or others) antenna switch and rotator switch.
  • Iluminated push buttons with labels.
  • Software updates via USB.

MBD-12F is an intelligent controller compatible with all twelve-antenna switches manufactured by Hamplus. It has a band decoder to receive the information coming from the connected radio equipment. In addition to antenna switching, the MBD-12F also offers eight frequency-driven GPOs (General Purpouse Output), one Band Data BCD Output, one output to command Band Pass Filter, 12 GPOs to automate the operation with TopBeam' s Waller Flag receiving antenna. The MBD-12F also commands the RS-24, RS-28, RS-44, RS-48 Rotator switches.


There are four ways that antennas and enabled rotators can be selected:

1) Manually by the front panel of the MBD-12F,
2) Manually by frequency or band change on the front panel of the transceiver,
3) Automatically by frequency or band change by the remotely controlled transceiver,
4) Automatically by a remotely controlled personal computer via LAN port to the MBD-12F.

On the front panel is a set of twelve illuminated push buttons for manual selection of antennas, twelve "Busy" LEDs to indicate which antennas are in use by other MBD-12F Controllers, eight LEDs to indicate rotator selection, one LED to indicate when the radio is transmitting, one LED to indicate the controller is in Split Antenna mode and one LED to indicate when the MBD-12F is connected to +13.8 Vdc power.
The MBD-12F receives from the transceiver the power supply (13.8VDC), the Send line and the information about the band in use. The controller recognizes the following Radios:

1- CI-V (Icom)
2- BCD (Yaesu and Elecraft)
3- RS-232 (Kenwood, Icom, Elecraft and Flex Radio)


Frequency Driven GPO:
The MBD-12F provides eight tuning points for automatically controlling shortened antennas with high Q coils. The tuning points are easily found by the operator using the radio and push buttons

Band Data Output:
The MBD-12F receives the radio information by CI-V (Icom), or by RS-232, or by BCD and provides a BCD output for use in external equipment.


Wiring diagram exemples:

12 antennas 2 radios and 8 rotators solution diagram


Band Pass Filter commands output:
The MBD-12F only needs one cable to automatically control most Band Pass Filters on the market.

Connection diagram of the Hamplus MDB-12F with Bandpass Filter

 

Waller Flag Receiving antennas:
The MBD-12F provides automation for the TopBeam Waller Flag receiving antennas with automatic filter exchange and the addition of an auxiliary keyboard to control the internal four-input Switch.

Diagram for connection to receiving antennas TopBeam Waller Flag

Remote operation:

Printed from the screen of the ROS-12, the MBD-12 remote control software for PC


Downloads:  
Remote Operation Software ROS-12  
ROS-12 Operation Guide  
MBD-12F Operation Manual v 2.6  
MBD-12F Connectors Pin Identification  
Firmware Update  

 

More Hamplus:
Copyright Hamplus .